This 1974 BMW 3.0 CSi Swapped Its M30 for a VAC-Built 4.1L S38 Stroker, and It Is Live at No Reserve

Elizabeth Puckett Elizabeth Puckett |
— 3 min read
| Add Motorious
Inka Orange 1974 BMW 3.0 CSi with a VAC-built S38 stroker engine, shown at dusk

The collector car market, in your inbox

Classic car news, hand-picked vehicles, and auction coverage. Choose what lands in your inbox.

Collectors usually prize BMW's E9 coupes for staying original. This 1974 BMW 3.0 CSi went the other way. The Inka Orange coupe on Cars & Bids has had its factory six replaced by a 3.5-liter S38 that, according to the seller, was bored and stroked to 4.1 liters by Pennsylvania-based VAC Motorsports. It is offered at no reserve, with a high bid of $39,300 and 11 bids as of Tuesday morning. The auction ends Thursday, November 20, at 1:36 p.m. EST.

A Different Six Than BMW Ever Fitted

A stock 3.0 CSi carried a 2,986 cc M30 inline-six with Bosch D-Jetronic fuel injection and roughly 200 horsepower. The S38B35 is a different animal: a 3,453 cc DOHC straight-six from BMW's late-1980s M cars, rated at 255 horsepower from the factory, with six individual throttle bodies, an iron block and an aluminum head. Fitting it to an E9 is the sort of swap that makes sense on paper and demands real fabrication in practice.

The seller says the engine was completely gone over by VAC Motorsports, a BMW performance and race shop known for engine builds. Listed internals include CP forged pistons and Arrow connecting rods, and the seller's comments say the head, camshafts, bearings, crankshaft and throttle bodies were all built as well. Intake duty falls to a Hartge carbon-fiber S38 plenum, with the piping routed low through an Alpina front air dam. A Remus exhaust, SPAL cooling fans with a Flex-a-Lite variable-speed controller and a trunk-mounted fuel cell round out the installation. The listing does not give a horsepower or dyno figure, so there is no documented output to quote. The seller points bidders to the build documentation in the listing's 359-photo gallery.

Drivetrain and Chassis Work

Power goes through a Precision Gearing close-ratio 265/5 dogleg five-speed, fitted with an S38 bell housing. Out back is an E9 differential with E30 internals built by Pete's Gear Shop. Wilwood front calipers, Koni rear shocks and ST front and rear sway bars handle the chassis side, and the listing notes factory BMW CSL chassis reinforcements. The CSL was the lightweight homologation special BMW introduced in 1972 to go touring car racing, so borrowing its structural bracing is a fitting choice for a car like this.

The body has been tuned to match. The front wheel arches are rolled and the rears widened and insulated with foam, which makes room for 17-inch HRE modular wheels. French-market-style yellow headlights, an Alpina front air dam and an LED third brake light finish the look. If BMW swaps are your thing, our look at a 1992 850Ci with an E46 M3 six-speed shows another way owners are updating older BMW drivetrains.

An Interior Built for Driving

Inside, the car wears Sebring leather upholstery and heated CSL-style front seats on BMW tilting brackets. The aftermarket steering wheel is wrapped in Alcantara, and the speedometer is a European-market unit. Practical additions include an auxiliary fuse panel, a rear-mounted circuit breaker, an alternator output control and a Split Second air-fuel ratio calibrator. The cabin is Saddle, a good match for the orange paint.

What the Listing Discloses

The odometer shows 1,000 miles on a five-digit unit. The car has a clean California title and is located in San Diego. It is being sold by KennanR, a Cars & Bids Certified Seller (private party), on behalf of the owner, who reportedly bought it in January 2011. The seller says the swap was done during a restoration that included a repaint, adds that the windows are tinted, and notes that the tires carry 2021 and 2022 date codes. Listed flaws include some exterior chips and scratches, misaligned trim on the driver's door and scratches on the center console. As with any older vehicle, emissions and registration rules vary by state, and the seller reminds bidders to check theirs before bidding.

Why It Stands Out

The appeal here is the engineering, not a headline number. A 4.1-liter S38 with individual throttle bodies, a dogleg gearbox and CSL-style reinforcement is a coherent plan for a classic BMW coupe, and the seller describes it as a passion project that spans more than a decade. Anyone interested should dig through the documentation in the gallery and read the comments before bidding, because most of the build details are the seller's own account. For comparison, we have also covered the 1974 BMW 2002 Turbo headed to Amelia and a 1974 MG BGT that swapped in a blueprinted Rover V8, two very different takes on 1970s European performance.

The full listing, photos and bidding are on Cars & Bids.

Great! Next, complete checkout for full access to Motorious.
Welcome back! You've successfully signed in.
You've successfully subscribed to Motorious.
Success! Your account is fully activated, you now have access to all content.
Success! Your billing info has been updated.
Your billing was not updated.